Feature request & ideas

This forum is empty.

Viewing 28 topics - 1 through 28 (of 28 total)

- Topic
- Voices
- Posts
- Last Post
- Slic3r users?
  Started by: stefaan
- 3
- 8
- 5 months ago
  mchmwel
- Fusion360 P Processor
  Started by: mark
- 1
- 1
- 5 months, 3 weeks ago
  mark
- Does the M0 pause command works on the Sigma?
  Started by: pablogil
- 1
- 4
- 5 months, 3 weeks ago
  sviver
- What’s next…..SIGMA/SIGMAX 19 future upgrades
  Started by: dario
- 1
- 2
- 9 months, 2 weeks ago
  dario
- Suggestion for IDEX mode
  Started by: arran.smith
- 1
- 1
- 10 months, 3 weeks ago
  arran.smith
- Feature request: Automatic Shut Down after print is done
  Started by: EmvioEng
- 8
- 9
- 1 year, 3 months ago
  pwalczak
- Suggestion for Bed Leveling
  Started by: evin.powell
- 1
- 1
- 1 year, 6 months ago
  evin.powell
- New feature request: Emergency / crash handling
  Started by: rod
- 2
- 2
- 1 year, 7 months ago
  arnauBCN3D
- Lower Bowden tube on right extruder
  Started by: klaus-peter.may
- 3
- 7
- 2 years, 1 month ago
  Technnical Support BCN3D
- Lack of Sigmax specific support?
  Started by: r.piola
- 3
- 6
- 2 years, 3 months ago
  BCN3D Technologies
- Duplication & Mirror Mode
  Started by: Adam
- 3
- 3
- 2 years, 9 months ago
  abl.gonzal
- LED Light control and a home position change?
  Started by: d.ward
- 4
- 6
- 2 years, 9 months ago
  abl.gonzal
- 1.75mm Filament upgrade kit
  Started by: maodch
- 2
- 2
- 2 years, 9 months ago
  shanecummings44
- 2mm Gap Between Heater & Glass Plate – why?
  Started by: lounigra
- 3
- 5
- 2 years, 10 months ago
  Neotko
- Upgrade kit for the sigma-> sigmax extruder?
  Started by: tobias.hagero
- 3
- 5
- 2 years, 11 months ago
  tobias.hagero
- Is It possible to print two same parts simultaneously?
  Started by: syue87
- 6
- 6
- 3 years, 3 months ago
  mattm
- Accessing SD card
  Started by: izikim.goldman
- 2
- 5
- 3 years, 5 months ago
  izikim.goldman
- Simultaneous Printing from 2 Extruders
  Started by: lemmans
- 2
- 5
- 3 years, 5 months ago
  lemmans
- Hardened nozzle for carbon-filled materials
  Started by: lifeimaging
- 9
- 16
- 3 years, 8 months ago
  BCN3D Technologies
- Filament stop detector?
  Started by: fred_dot_u
- 3
- 5
- 4 years, 1 month ago
  fred_dot_u
- heating bed to 100
  Started by: shackman0
- 3
- 3
- 4 years, 1 month ago
  Phill
- Thermal Runaway Protection
  Started by: Phill
- 1
- 1
- 4 years, 3 months ago
  Phill
- Does the Sigma electronics have buzzer?
  Started by: pablogil
- 2
- 3
- 4 years, 4 months ago
  pablogil
- Much more control!
  Started by: rubin.khatib
- 2
- 2
- 4 years, 5 months ago
  roger uceda
- Maximum spools size
  Started by: pyniec
- 2
- 3
- 4 years, 6 months ago
  pyniec
- Feature request: Filament Sensor
  Started by: EmvioEng
- 1
- 1
- 4 years, 6 months ago
  EmvioEng
- Enhancement requests
  Started by: guido
- 1
- 2
- 4 years, 6 months ago
  guido
- Interchangeable nozzle?
  Started by: pyniec
- 2
- 5
- 4 years, 6 months ago
  pyniec

Viewing 28 topics - 1 through 28 (of 28 total)

You must be logged in to create new topics.